Register Mac Address With Comcast For New Modem

During the initial setup the device display cycles through 14 activation steps and takes 30-60 minutes.This method allows you to then force any config file, but it associates your modem Cloning Comcast Mac Address Dec 15, 2012. Verify the Power / Status LED indicator is solid blue. Reference the device display to determine the Network Extender status. The use of a surge protector is recommended. Connect the power adapter to an available power outlet.

Register Address With Comcast For New Modem Install Steps And

Running installation for the Truemobile 2300, the system verifies my internet connection and runs through the regular install steps and then fails to achieve an internet connection. My cable provider is Comcast and I currently use a Linksys cable modem. I'm trying to connect the 2300 to my existing cable modem connection via my Dimension 4100 (running Windows XP).

Clearly, the router is not defective. I went through all the steps and it did the exact same thing as the first one. Two frustrating weeks later, a new 2300 router arrived.

Before you begin, make sure you have your account information from your ISP. Any help would be greatly appreciated.Connect your Mac to the internet using a cable modem. I figure there must be a setting or something that is not right, but I can't bear the thought of another 2 hour call to tech support. Putting the network cables back to their original connection instantly re-establishes my internet connection.

You can disable this type of software by clicking Start -> Settings -> Control Panel -> Add or Remove Programs. These types of software will no longer be needed when you network your systems with this router. After you have your information, connect your cable modem to your computerвЂ™s Ethernet port, turn the modem on, then follow these instructions to enter the information in Network preferences.You should disable any connection sharing software on your computer(s) - such as Microsoft Internet connection Sharing (ICS), 3Com HomeClick and Intel Anypoint ISS - and proxy software - such as Wingate and Sygate.

This can be verified by the presence of the arrow on its connection status window. Call 1-855-OK-BEGIN (1-85).Use the Control Utility to first determine where the connectivity is broken. If you have digital adapters, have the serial numbers for those ready as well. If the online activation service isn't working, you can activate over the phone: Have your account number and cable box serial number handy. Activate by calling Comcast.

Make sure the computer's IP settings are correct: Open a DOS command prompt window, type ipconfig, and press. Check the physical network cable connections for the computer. Make sure the TCP/IP stack is successfully installed. For assistance, refer to the documentation that was shipped with the adapter. Make sure the network adapter is successfully installed. To review the connection status for the wireless network, start the web-based configuration tool and click the Device Status tab.

PC finds router and gets ip address. Third step - connect router (through available port) to NIC with second Cat5 cable. Second step - remove cable connecting NIC to cable modem from NIC and plug in into 'Internet' slot on router. It does that successfully. First step - verify internet connection. I'm following the installation wizard that came with the Truemobile 2300.

The host name that is filled in is the service number of my computer, but I'm told Comcast doesn't require a host name or domain name, so I delete the service number of the computer and uncheck the box. When I check the Basic Settings for the router, it has a check mark by 'ISP requires host name and domain name' and a check mark beside 'ISP requires you to input WAN ethernet Mac'. I pull up the browser/control for the router and check status - it shows the connection between the PC (NIC) and the router is good, but no connection between router and internet.

If the LAN Mac address needs to be changed so it is the same as the WAN Mac (is this what you refer to when you mention cloning the Mac address?) then I don't know how to change that. I believe the number it is showing for the LAN Mac address is the Mac address of the router. When I go to check status on the router control utility, it shows the WAN Mac address as being my computer's physical address and it shows a different number for the LAN Mac address.

Any other thoughts? Thanks. I'm really at a loss to figure out why I'm not getting a router/internet connection. Even after the settings are saved, if I shut the whole system down and turn it on again, the old settings always return.

Register Mac Address With Comcast For New Modem